丨
| Quantity: | |
|---|---|
This Pre‑Wired Switched Australian Rack PDU is a 19‑inch 1U horizontal rack‑mount finished power distribution unit engineered for Australian and New‑Zealand multi‑site roll‑out projects. Distinct from bare‑base VH‑4061 (requires full on‑site module assembly) and 2U dual‑deck high‑density VH‑4062 (blank chassis for massive outlet counts), this unit comes completely factory pre‑wired with illuminated master power toggle and genuine AS/NZS 3112 Type‑I outlets.
No in‑field module assembly or internal wiring work is required. Rated for 16A / 4000W @240VAC, built with thermally‑optimised extruded‑aluminium housing and CE & RoHS compliant. It targets integrators and local resellers prioritising fast site commissioning, where full chassis‑level re‑configurability is not mandatory.
Core positioning: Factory‑completed ready‑to‑run AU‑NZ switched PDU; minimises on‑site assembly labour for branch‑office, education and surveillance roll‑outs; limited hot‑swap slots for later incremental upgrades, cannot achieve complete chassis reconstruction like VH‑4061 bare chassis.
1.Factory‑Assembled & Load‑Validated To Cut AU‑NZ On‑Site Labour Costs
Australian‑New‑Zealand field‑service labour carries relatively high hourly rates. Unlike VH‑4061 bare chassis that forces technicians to select, fit and wire each module on‑location, VH‑4063 finishes socket‑switch interconnections plus full continuity‑load impulse testing inside factory. After delivery installers only perform rack fixation and mains termination. It lowers total project expenditure and eliminates hidden contact‑fault risks caused by imperfect manual field wiring.
2. Native AS/NZS 3112 Type‑I Socket Bank Satisfies Local Compliance Checks
Every flat‑pin receptacle passes batch factory validation. Generic multi‑purpose universal PDUs often deployed in cross‑border projects rely on adaptors; adaptor‑joint over‑heating frequently triggers non‑compliance remarks during Australian and New‑Zealand site acceptance audits. Native Type‑I geometry directly works with local equipment plugs, assisting integrators to smoothly finish acceptance for education, commercial and public‑sector tender deployments.
3. Front‑Side Illuminated Toggle Optimised For Compact AU‑Style Server Closets
Numerous local SME cabinets adopt shallow‑depth compact designs, leaving very limited rear‑side operating clearance. The back‑lit master‑switch sits on front faceplate. Technicians execute full‑bank power isolation for hardware swap‑outs and observe LED power‑status indicator without reaching deep into tangled rear‑cable zones, improving daily‑maintenance operational safety.
4. Aluminium Profile Tuned For AU‑NZ Variable Ambient Cabinet Temperatures
Extruded‑aluminium housing is thermally calibrated for this pre‑defined outlet‑bank load profile. Many Australian server‑rooms face elevated ambient temperatures in summer seasons. Compared to steel‑bodied alternatives, it achieves improved passive heat dissipation under mixed‑device continuous‑load, slows socket‑contact ageing and reduces static‑weight burden on cabinet mounting rails.
5. Limited‑Slot Incremental‑Upgrade Without Complete Chassis Rebuild
Although shipped as finished pre‑wired unit, reserved auxiliary bays allow technicians to retrofit SPD surge‑protection, power‑metering or USB‑charging modules when project‑requirements evolve. Critical hardware limitation: existing internal wiring layout does not support large‑scale rearrangement of outlets and control components. If your project demands total layout re‑work, select VH‑4061 bare‑chassis variant.
6. Turn‑Key Documentation Pack Suited For Mid‑Scale AU‑NZ Tender Bids
Complete finished‑unit batch‑test‑reports are supplied alongside CE / RoHS files. Documents meet typical checklist requirements for Australian‑New‑Zealand mid‑sized commercial and education‑sector tender submissions. OEM silkscreen private‑label marking is available for bulk‑order local reseller ready‑stock SKU programmes.
1. Australian SME branch‑office server closets: Distributed corporate satellite‑site IT racks; ready‑built hardware reduces expensive on‑site assembly work for multi‑location roll‑out programmes.
2. New‑Zealand education‑site small‑scale IT‑cabinet projects: School and polytechnic IT closets for mid‑scale tender‑procurement with standardised technical‑spec requirements.
3. Standard surveillance‑recording‑rack deployments AU‑NZ: Security‑system integrator projects requiring fast commissioning for multi‑site CCTV infrastructure.
4. Local AU‑NZ reseller off‑the‑shelf inventory stock: Pre‑validated finished‑SKU enabling fast‑order fulfilment; no need for reseller warehouses to perform in‑house module assembly.
5. Commercial‑building retro‑fit cabinet‑projects: Existing cabinet‑upgrade jobs needing pre‑tested switched power distribution without bespoke chassis customisation.
| Item | Details |
| Minimum Order | 1 unit |
| Customization | Input cable length, OEM silk‑screen logo, pre‑fit limited retrofit modules (bulk orders) |
| Production Capacity | 300 units / month |
| Lead Time | 7‑15 working days for standard pre‑wired unit |
| Packing | Standard export carton |
| Trade Terms | FOB, CFR, CIF, EXW |
Q: How do I choose between VH‑4063, VH‑4061 and VH‑4062 Australian‑series PDUs?
A: Pick VH‑4063 for switched ready‑to‑deploy projects aiming to minimise AU‑NZ on‑site assembly labour. VH‑4061 is bare‑chassis for projects requiring total custom‑module layout. VH‑4062 is 2U dual‑deck blank chassis built for ultra‑high‑outlet‑count racks. All three adopt AS/NZS 3112 Type‑I sockets and share partial‑module‑compatible ecosystem.
Q: Are sockets and master‑switch factory‑load‑tested on VH‑4063?
A: Yes. Every socket and master‑switch circuit passes continuity and simulated‑load testing within factory, lowering failure‑risks arising from manual on‑site wiring work.
Q: Can I fully rebuild and re‑arrange all internal modules of VH‑4063 later?
A: No. It is factory‑pre‑wired finished‑unit; you may add SPD / meter / USB auxiliary‑modules into reserved slots, but core power‑circuit layout cannot be completely re‑configured. For total re‑configurability, select VH‑4061 bare‑chassis.
Q: Is VH‑4063 compliant for both Australian and New‑Zealand cabinet‑installations?
A: Yes. AS/NZS 3112 represents shared socket‑norm for both territories, complying with local cabinet‑electrical‑installation requirements.
Q: Does reversed rear‑feed mounting change thermal‑dissipation performance?
A: No. Dual‑orientation mounting only alters cable‑exit‑direction; aluminium heat‑dissipation performance and electrical‑safety‑indicators remain unchanged, fitting diverse AU‑NZ cabinet‑wiring‑layouts.
Q: Are test‑documents sufficient for AU‑NZ mid‑scale tender‑audit‑procedures?
A: Yes. Finished‑unit test‑reports plus CE / RoHS documentation are included, matching typical document‑requirements for Australian‑New‑Zealand commercial‑and‑education‑sector tender‑projects.
