丨
| Quantity: | |
|---|---|
This Pre‑Wired Switched Swiss Rack PDU is a 19‑inch 1U horizontal rack‑mount pre‑wired switched PDU purpose‑built for Switzerland and Liechtenstein SME‑grade cabinet deployments. Distinct from bare‑chassis VH‑4069 (requires full on‑site module assembly for total customisation) and switch‑less VH‑4071 (always‑on for 24/7 critical loads), this unit comes fully factory pre‑assembled with illuminated master power toggle and native SEV 1011 Type‑J Swiss sockets. No on‑site component fitting or internal wiring work is needed.
Rated for 10A / 2500W @230VAC, built with thermally‑calibrated extruded‑aluminium housing and CE & RoHS compliant. It is optimised for projects where fast on‑site commissioning is prioritised over full‑chassis re‑configurability, perfectly matching high‑labour‑cost conditions common within Swiss IT‑installation markets.
Core positioning: Factory‑pre‑wired ready‑to‑run switched Swiss‑spec PDU; minimises field‑assembly workload for Swiss SME, branch‑office and surveillance‑rack roll‑outs; partial hot‑swap upgrade slots reserved, yet not supporting complete chassis reconstruction.
1.Factory Fully‑Assembled & Load‑Tested To Cut Swiss On‑Site Labour Burden
Switzerland’s high on‑site technician‑hour cost makes field‑assembly a major project‑expense driver. Unlike bare‑chassis VH‑4069 that demands module selection, fitting and wiring on‑location, VH‑4070 completes all socket‑switch interconnections plus full continuity / load impulse testing inside factory. After delivery, installers only complete rack‑fixing and mains‑cable termination. It lowers total project expenditure and eliminates human‑wiring‑induced hidden contact‑fault risks.
2. Native SEV 1011 Type‑J Socket Bank Meets Swiss Local Compliance Audits
Genuine SEV 1011 Type‑J shuttered receptacles are pre‑mounted and batch‑tested. Many multi‑national generic PDUs rely on adapters to work with Swiss plugs; adapters frequently trigger non‑conformity remarks during local electrical‑safety inspections. This native‑socket design avoids adapter‑related over‑heating hazards and assists integrators to smoothly pass acceptance checks for Swiss commercial and education‑sector projects.
3. Front‑Side Illuminated Toggle Tuned For Compact Swiss‑Style Cabinets
Numerous Swiss SME cabinets adopt compact shallow‑depth designs, leaving very limited rear‑side operating‑space. The illuminated master‑switch sits on front face; technicians can perform full‑bank power cut‑off for hardware replacement and directly observe power‑status LED without reaching deep into cramped cabinet interiors, improving daily‑maintenance operational‑safety.
4. Load‑Matched Aluminium Profile Optimised For SME Mixed‑Device Thermal Conditions
Extruded‑aluminium housing is thermally calibrated for this pre‑defined socket‑bank load‑profile. It efficiently dissipates cumulative heat generated by mixed office IT equipment (switches, NAS, surveillance recorders). Compared with steel‑bodied alternatives, it reduces internal hot‑spot build‑up, slows socket‑contact ageing and eases static‑weight load applied to cabinet mounting rails.
5. Limited‑Slot Incremental‑Upgrade Without Full‑Chassis Re‑Build
Though shipped as finished pre‑wired unit, reserved auxiliary bays allow field technicians to retrofit SPD surge‑protection, power‑metering or USB‑charging modules if project‑requirements evolve in later phases. Important limitation: hardware‑wiring architecture does not permit large‑scale re‑arrangement of core outlet and control layout; for fully‑re‑configurable use‑cases you need VH‑4069 bare‑chassis variant.
6. Project‑Ready Documentation Suited For Mid‑Scale Swiss Tender Bids
Full finished‑unit batch‑test‑reports are provided alongside CE / RoHS files, satisfying documentation‑check‑lists for mid‑sized Swiss commercial, education‑sector tender submissions. OEM silkscreen private‑label marking is available for bulk‑order local Swiss reseller ready‑stock SKU programmes.
| Category | Specification |
| Model | VH‑4070 |
| Form Factor | 1U horizontal rack‑mount, 19" EIA standard |
| Socket Standard | SEV 1011 Type‑J Swiss standard, 10A 230VAC, factory pre‑wired |
| Built‑in Control | Front‑panel illuminated master power switch |
| Rated Voltage | 220–240VAC 50Hz |
| Max Rated Current | 10A |
| Max Power Output | 2500W |
| Housing Material | Extruded aluminium alloy |
| Overall Dimensions | 482.6 × 45 × 45 mm (L×W×H) |
| Mounting | Adjustable dual‑orientation mounting lugs: forward‑facing / reversed rear‑feed |
| Included Accessories | M6 mounting hardware, lock washers, installation‑operation manual |
| Certifications | CE, RoHS compliant; sockets to SEV 1011 standard |
| Input | Swiss‑standard mains plug; IEC C14 inlet optional; 2‑metre standard cord, custom lengths available |
1. Swiss SME small‑and‑medium enterprise server closets: Office IT racks for corporate branch‑sites; ready‑deploy hardware reduces expensive field‑assembly labour for multi‑site roll‑outs.
2. Branch‑office network cabinets across Switzerland and Liechtenstein: Distributed satellite‑office infrastructure, convenient front‑panel power isolation for periodic hardware‑swap‑out maintenance.
3. Standard surveillance‑camera recording rack deployments: Small‑to‑medium CCTV systems, quick commissioning for security‑system integrator projects.
4. Swiss education‑site small‑scale IT‑cabinet projects: School and vocational‑college IT closets for mid‑scale tender‑procurement with moderate technical‑spec requirements.
5. Local Swiss reseller off‑the‑shelf inventory stock: Pre‑tested finished‑SKU for fast‑order fulfilment, no need for in‑house module‑assembly work by reseller warehouses.
Deployment note: This unit supports partial‑function retrofit. If your project requires full‑flexibility re‑arrangement of every outlet and control position, select VH‑4069 bare‑modular chassis instead.
| Item | Details |
| Minimum Order | 1 unit |
| Customization | Input cable length, OEM silk‑screen logo, pre‑fit limited retrofit modules (bulk orders) |
| Production Capacity | 300 units |
| Lead Time | 7‑15 working days for standard pre‑wired unit |
| Packing | Standard export carton |
| Trade Terms | FOB, CFR, CIF, EXW |
Q: How do I choose between VH‑4070, VH‑4069 and VH‑4071 Swiss‑series PDUs?
A: Pick VH‑4070 for switched ready‑to‑deploy projects where you want to minimise Swiss‑site field‑assembly labour. VH‑4069 is bare‑chassis for projects demanding complete custom‑module layout. VH‑4071 is switch‑less always‑on variant built exclusively for 24/7 non‑stop critical loads. All three adopt SEV 1011 Type‑J sockets and share partial‑module‑compatible ecosystem.
Q: Are sockets and master‑switch factory‑load‑tested on VH‑4070?
A: Yes. Every socket and master‑switch circuit passes continuity and simulated‑load testing within factory, lowering failure‑risks arising from manual on‑site wiring work.
Q: Can I fully rebuild and re‑arrange all internal modules of VH‑4070 later?
A: No. It is factory‑pre‑wired finished‑unit; you can add SPD / meter / USB auxiliary‑modules into reserved slots, but core power‑circuit layout cannot be completely re‑configured. For total re‑configurability, use VH‑4069 bare‑chassis.
Q: Is VH‑4070 compliant for both Switzerland and Liechtenstein cabinet‑installations?
A: Yes. SEV 1011 Type‑J represents shared socket‑norm for both territories, complying with local cabinet‑electrical‑installation requirements.
Q: Does reversed rear‑feed mounting change thermal‑dissipation performance?
A: No. Dual‑orientation mounting only alters cable‑exit‑direction; aluminium heat‑dissipation performance and electrical‑safety‑indicators remain unchanged, fitting diverse Swiss cabinet‑wiring‑layouts.
Q: Are test‑documents sufficient for Swiss mid‑scale tender‑audit‑procedures?
A: Yes. Finished‑unit test‑reports plus CE / RoHS documentation are included, matching typical document‑requirements for Swiss commercial‑and‑education‑sector tender‑projects.
